china wholesaler 15HP Diesel Hand tractor rotary tiller manufacturers

Solution Description

15HP Diesel Hand tractor rotary tiller

1.Item description:
Walking tractor
The hand-held tractor is a traction and driving variety tractor, which is compact, sturdy and reputable, adaptable in operation, very good in passability, and outfitted with using gear. The hand-held tractor has increased horsepower and effectiveness, and is suited for paddy area dryland and farming in orchards, vegetable gardens, vegetable gardens and hilly locations. Plowing, rotary tilling, rotary fielding, trenching, sowing, transportation and other functions can be carried out with the corresponding agricultural implements and components.
This merchandise has the traits of big CZPT , modest size, mild fat, straightforward to begin, minimal gas intake, very good reliability, hassle-free procedure and maintenance, vast software, and so forth. It is extensively used in walking tractors, agricultural tricycles, h2o pumps, generator sets, small Supporting CZPT for machinery this sort of as ships, crushers, and little building machinery. It is also utilised with a rotary tiller tiller.

Technical Parameters

Product XGJ-fifteen
Power 15HP
Cultivated land width 120cm
Cultivated land depth 35cm
Water cooled diesel motor product R1100
Optional seats, rotary knives, weeding wheels, turning ploughs, ridgers, electrical starters, openers, paddy wheels, and so forth.

A lot more image:

1).Preparation before commencing
Careful inspection of the locomotive ahead of use can eradicate concealed hazards and efficiently avoid accidents. Usually, the diesel motor and the chassis must be inspected for oil leakage, air leakage and water leakage. Verify if the cooling drinking water of the diesel engine is adequate. Check the oil amount and good quality of the oil pan lubricant. Examine the oil amount of the gearbox oil. Unscrew the oil inspection screw plug on the tank, so that the equipment oil can overflow from the screw gap. If it is insufficient, incorporate it. Check the stress of the V-belt. The belt is also free and need to be adjusted. Check out tire stress. If the air strain is too low, it must be made up.
two )diesel engine commence
Pull the tractor’s clutch brake handle to the off place. Spot the shift lever in the CZPT position. Shift the throttle handle to the beginning placement. CZPT the decompression take care of with your remaining hand and maintain the starter take care of with your proper hand to shake the crankshaft of the diesel motor. Steadily enhance the velocity, the remaining hand speedily relaxes the decompression take care of, and the proper hand proceeds to speed up the shaking until finally the diesel motor begins.
Soon after the diesel motor is started out, check if the oil strain indicating valve is elevated. Pay attention to the sound of the diesel motor. Observe the smoke. Right after confirming that everything is normal, let the diesel engine run for a whilst, so that the water temperature rises to forty-sixty degrees.
3) tractor commence
Following warming up, you can begin. At the begin, lift the CZPT assist of the tractor up. Do not hold the steering take care of, swing the handrail still left and correct right up until it stops. Pull the clutch brake lever to the “off” place. Shift the shift lever and area it in the wanted equipment situation. Place the clutch brake handle from “off” to the “closed” situation, creating the tractor to little by little begin shifting. Handle the throttle in accordance to the amount of traction load
four) shifting
When the tractor is in procedure, when the load and street problems modify and the traction or driving speed needs to be modified, it can be recognized by shifting. Prior to shifting gears, speedily pull the clutch brake take care of to the “off” placement. Hold the shift lever to the desired placement, push it to the remaining for low equipment, and pull it to the right for substantial gear. Slowly and gradually combine the clutch and the tractor will get the corresponding pace.
five )steering
The steering of the strolling tractor is accomplished by manipulating the still left and proper steering handles. When turning, you should very first decrease the throttle to lessen the speed. Then, pinch the correct steering manage and change to the appropriate. Pinch the left steering handle and switch remaining. Make tiny adjustments during straight-line driving. You do not want to pinch the steering handle, just thrust the armrest. When outfitted with a trip, press the appropriate foot pedal forward, turn the tractor to the right, press the left foot pedal ahead, and change the tractor to the still left.
6 )brake parking
The brake handle of the strolling tractor is created with the clutch deal with. The clutch rocker arm and the brake rocker arm are also created in one particular piece. When the manage is pulled from the engaged situation to the disengaged position, the arm swing angle is modest and the braking effect is not acquired. The manage continues to pull back, the swinging arm swing angle will increase, and the brakes start to act, causing the tractor to stop. If you hang the trailer, you also want to phase on the trailer brake at the very same time. Right after the tractor stops, release the brake. In order to avert the clutch spring from getting older, set the clutch manage to the “closed” position, allow the diesel engine idle for a couple of minutes at low speed, steadily decrease the h2o temperature and oil temperature, and then close the throttle to extinguish.
Be careful not to slam the throttle ahead of turning off the flame. Right after the flame is turned off, turn off the tank swap. Flip the flywheel to area the piston at leading dead middle. CZPT er defense of the device.
two.Walking tractor maintenance storage:
If the strolling tractor is not employed for a CZPT time, there will be a collection of problems and malfunctions. In purchase to steer clear of failure when using once again, pay consideration to the upkeep steps.
one. Parking spot. It need to be put in the warehouse, but not put collectively with chemical fertilizers and pesticides to avoid it from corroding the elements if parked outdoor, pick a high-lying, dry and ventilated location, and go over it with a plastic fabric to avert mechanical damage and Corrosion.
two. Pad equipment areas. The tractor need to be padded with wood piers or masonry to minimize the load on the tires. If the pads are not supported, the tires should be enhanced by ten% to 20%, and ought to be inspected frequently, typically inflated, and not insufficiency.
3. Clean totally. Eliminate the filth and oil on the exterior of the tractor, and totally examine, change, and tighten the areas and screws to prevent loosening.
4. Set thoroughly clean oil. Following the tractor is deactivated, the cooling drinking water, diesel oil, and motor oil in the motor need to be completely removed.
5. Routine maintenance of the device. Get an acceptable sum of dewatering machine oil (warmth the oil to about a hundred thirty °C) and pour into the consumption pipe to rotate the crankshaft so that the oil adheres to the piston, piston rod, cylinder liner and valve. Shake the piston to the compression leading useless heart to prevent the valve spring, push rod and other elements from getting pressed for a CZPT time and get rid of their functionality.
six. Get rid of the injector. Soon after cleaning the injector, put it into thoroughly clean diesel, loosen the changing screw, and block the injector chamber with a cork.
seven. Fill the axle box with oil. Consider 1kg of dehydration oil, pour into the crankcase, and then change the crankshaft a handful of turns to make the lubrication program entire of dehydration oil.
8. Elements of polyester oil. Apply the dehydration oil to the CZPT ening areas these kinds of as the rocker arm, substantial strain oil pipe, gas injection, bolts and nuts to avert rust.
9. Lubricate nicely. In accordance to the general lubrication demands of the tractor, choose the lubricating oil that meets the standard for complete lubrication.
ten. Bandaged and dustproof. The air filter, exhaust pipe, drinking water tank port, gas tank port, etc. of the engine are easily place into the dust, and bundled with plastic cloth or oil paper to avoid entry of debris and dust.
Our manufacturing facility:


Gear reducers, also named reducers, arrive in a number of transmission types and are designed to multiply torque and lessen input velocity to a sought after output velocity. The primary advantage of inline gearboxes is their capability to maintain control in apps involving substantial rotational speeds. Their efficiency and capacity to supply higher enter speeds with small backlash make inline reducer gearboxes perfect for a vast selection of movement handle applications
china wholesaler 15HP Diesel Hand tractor rotary tiller manufacturers